Wire-wrapped Fascinating Sterling Silver Cuff Bracelet




Products Necessary
24" eighteen-gauge sterling silver wire
Pre-made sterling silver cuff bracelet
(You may make your own cuff bracelet from hefty
gauge sterling silver rectangle wire if you like.)
Instruments NEEDED
Liver of sulfur or oxidizing Remedy
Ruler
Marker
Spherical nose pliers Wire cutters or tin snips File
Chain nose pliers Great steel wool Polishing cloth Basic safety Eyeglasses
one. Utilize liver of sulfur or oxidizing solution to the 24" of 18-gauge sterling silver wire.
It is essential to observe any basic safety suggestions the company implies on the Instructions when dealing with any substances. You'll use the fantastic steel wool about the oxidized wire to get rid of several of the darkened parts When you comprehensive the wrapping course of action.
2.Use the ruler to measure and mark the 24" of 18-gauge wire into 4 sections. Measure and mark the wire at 7", 12*. and 17".
three.Future, evaluate and mark the center of the very best in the cuff bracelet (because it’s curved, you are able to just type of eyeball it). Then use the ruler to measure and mark %" from the middle with the cuff to each side.
four.Firmly grasp the marked Heart on the 24" 18-gauge wire during the jaws of your round nose pliers. Use your fingers to bend the edges right down to type an upside-down U shape (the wire will resemble a large bobby pin).
When dealing with very long items of wire, security Eyeglasses are advisable.
5.Slide the wire on to the sterling silver cuff bracelet to the center mark. Pinch the wire limited on to the cuff bracelet and, although Keeping the wire to the cuff along χειροποίητα ανδρικά δαχτυλίδια with your fingers, wrap a person side of the wire randomly toward the Vi' mark that you choose to designed on the top of your cuff bracelet. You'll want to watch where by the 7" as well as 17' marks are over the wire and use them to match up Together with the Vi" κοσμήματα φθηνά mark that you simply built to the cuff bracelet.

eight. Make use of the spherical nose pliers to curl the ends with the wire up into your wrapped wire about the underside of your cuff bracelet. Use the chain nose pliers to firmly squeeze the μονόπετρο γάμου finally ends up into the other wrapped wire. This will likely keep the ends securely in place.
six.Finish wrapping the wire on the opposite side, matching up the 7" and also the 17" marks around the cuff bracelet Together with the Vi" marks monopetro around the 18-gauge wire.
seven.Now wrap the wire on 1 aspect again toward the center with the cuff bracelet. Then wrap the wire on the opposite side in the cuff bracelet back again towards the middle. You may need to trim and file the ends on the wire so they finish up within the backside in the cuff bracelet.
9. Use fantastic metal wool to eliminate the darkened area within the surface area with the wire, leaving the parts during the crevices from the wrapped wire dim. Buff the wrapped wire and also the cuff bracelet using a sharpening fabric.
What assistance would you present you with a commencing artist?
Λ portrait Trainer once informed me that from the 500th portrait I could be truly excellent. Lesson-follow; apply daily.
Persist with one particular medium and do it very well. Craftsmanship is key.
This cuff is great for φθηνό μονόπετρο Males as well as Ladies. Use the larger Males's size of pre-made cuff bracelet and add extra duration on the 18-gauge sterling silver wire, typically six to 8 inches to support
the more substantial Guys’s cuff bracelet.

Wire-wrapped Pretty Sterling Silver Cuff Bracelet




MATERIALS Wanted
24" 18-gauge sterling silver wire
Pre-manufactured sterling silver cuff bracelet
(You can also make your very own cuff bracelet from heavy
gauge sterling silver rectangle wire if you like.)
Resources Wanted
Liver of sulfur or oxidizing Answer
Ruler
Marker
Round nose pliers Wire cutters or tin snips File
Chain nose pliers Great steel wool Polishing cloth Basic safety Eyeglasses
one. Apply liver of sulfur or oxidizing Remedy to your 24" of eighteen-gauge sterling silver wire.
It is vital to observe any basic safety tips the company suggests over the directions when working with any chemical compounds. You are going to use the fantastic steel wool to the oxidized wire to get rid of some of the darkened parts When you finish the wrapping process.
2.Use the ruler to measure and mark the 24" of 18-gauge wire into four sections. Evaluate and mark the wire at 7", 12*. and 17".
3.Next, measure and mark the middle of the very best with the cuff bracelet (because it’s curved, you'll be able to just sort of eyeball it). Then make use of the ruler to measure and mark %" from the middle of your cuff to either side.
4.Firmly grasp the marked Centre of your 24" 18-gauge wire inside the jaws in the spherical nose pliers. Make use of your fingers to bend the sides all the way down to variety an upside-down U form (the wire will resemble a substantial bobby pin).
When working with extended parts of wire, basic safety glasses are advised.
5.Slide the wire onto the sterling silver cuff bracelet to the center mark. Pinch the wire limited onto the cuff bracelet and, although Keeping the ασημένια κολιέ ονόματα wire to the cuff along with your fingers, wrap one facet on the wire randomly towards the Vi' mark that you just created on the top with the cuff bracelet. You will want κοσμήματα γυναικεία to look at in which the seven" as well as the seventeen' marks are within the wire and rely on them to match κοσμήματα ασημένια up Together with the Vi" mark which you made to the cuff bracelet.

eight. Make use of the spherical nose pliers to curl the ends of your wire up in to the wrapped wire over the underside of the cuff bracelet. Use the chain nose pliers to firmly squeeze the winds up into one other wrapped wire. This can continue to keep the finishes securely in place.
6.End wrapping the wire on the other aspect, matching up the seven" and also the 17" marks to the cuff bracelet Using the Vi" marks to the eighteen-gauge wire.
seven.Now wrap the wire on 1 aspect again toward the center in the cuff bracelet. Then wrap the wire on the opposite facet from the cuff bracelet back toward the center. You might require to trim and file monopetra times the finishes of your wire so that they wind up to the bottom of the cuff bracelet.
nine. Use fine steel wool to get rid of the darkened place on the surface in the wire, leaving the regions during the crevices of the wrapped wire dark. Buff the wrapped wire as well as the cuff bracelet using a sharpening fabric.
What assistance would you present you with a commencing artist?
Λ portrait Trainer at the time told me that from the 500th portrait I could be truly excellent. Lesson-follow; follow daily.
Persist with one particular medium and do it very well. Craftsmanship is key.
This cuff is great for Males in addition to Females. Use the οικονομικά μονόπετρα greater Gentlemen's measurement of pre-created cuff bracelet and incorporate added length for the 18-gauge sterling silver wire, usually 6 to 8 inches to accommodate
the greater Guys’s cuff bracelet.

Wire-wrapped Pleasing Sterling Silver Cuff Bracelet




Components NEEDED
24" 18-gauge sterling silver wire
Pre-built sterling silver cuff bracelet
(You can make your own private cuff bracelet from major
gauge sterling silver rectangle wire if you prefer.)
Equipment Desired
Liver of sulfur or oxidizing Answer
Ruler
Marker
Round nose pliers Wire cutters or tin snips File
Chain nose pliers High-quality metal wool Polishing cloth Security glasses
1. Use liver of sulfur or oxidizing Resolution on the 24" of 18-gauge sterling silver wire.
It is critical to comply with any basic safety tips the company suggests on the Instructions when dealing with any chemicals. You'll make use of the wonderful metal wool over the oxidized wire to remove several of the darkened parts When you comprehensive the wrapping course of action.
2.Make use of the ruler to measure and mark the 24" of 18-gauge wire into four sections. Evaluate and mark the wire at 7", 12*. and seventeen".
three.Subsequent, measure and mark the center of the top from the cuff bracelet (mainly because it’s curved, you can just type of eyeball it). Then use the ruler to evaluate and mark %" from the center in the cuff to each side.
four.Firmly grasp the marked Middle in the 24" eighteen-gauge wire while in the jaws on the round nose pliers. Make use of your fingers to bend the sides down to variety an upside-down U condition (the wire will resemble a considerable bobby pin).
When dealing with extended parts of wire, basic safety glasses are suggested.
five.Slide the wire onto the sterling silver cuff bracelet to the middle mark. Pinch the wire restricted onto the cuff bracelet and, though Keeping the wire within the cuff with your fingers, wrap just one side of your wire randomly toward the Vi' mark you manufactured on χειροποίητα ανδρικά δαχτυλίδια the very best of the cuff bracelet. You'll want to view where by the 7" as well as 17' marks are over the wire and use them to match up Together with the Vi" mark that you simply built about the cuff bracelet.

eight. Use the spherical nose pliers to curl the ends with the wire up in the wrapped wire within the underside with the cuff bracelet. Utilize the chain nose pliers to firmly squeeze the ends up into the opposite wrapped wire. This may hold the finishes securely set up.
6.End wrapping the wire on the other aspect, matching up the seven" and the 17" marks to the cuff bracelet with the Vi" marks around the 18-gauge μονόπετρο γάμου wire.
seven.Now wrap the wire on a person side back toward the center of your cuff bracelet. Then wrap the wire on the other side on the cuff bracelet again towards the middle. You may need to trim and file the ends in the wire so they turn out over the bottom of your cuff bracelet.
nine. Use fine steel wool to remove the darkened spot κολιέ ονόματα about the floor of your wire, leaving the areas inside the crevices with the wrapped wire darkish. Buff the wrapped wire plus the cuff bracelet that has a sprucing fabric.
What advice would you provide a beginning artist?
Λ portrait teacher after instructed me that κοσμήματα ασημένια via the 500th portrait I could be truly excellent. Lesson-follow; apply each day.
Stick to one medium and do it rather well. Σταυροί βάπτισης Craftsmanship is essential.
This cuff is perfect for Adult men together with Gals. Utilize the much larger Adult men's measurement of pre-manufactured cuff bracelet and incorporate further size towards the 18-gauge sterling silver wire, generally 6 to eight inches to accommodate
the larger men’s cuff bracelet.

Finest Jewellery Basics





Fundamental Wire Loops
For finest success, use both chain-nose and round-nose pliers.
Method two – Bend then cut
Method one – Slash then bend
Process three – Utilize the one-Action Looper
one two three
4 5 six
With the Beadsmith® R&T Merchandise #69-055
Trim and loop eye pins in one movement. Will work with three/8” wire and
more time. Use lifeless-soft or 50 %-really hard cherished steel wire, craft wire, and
copper or brass Main wire. Use with wire among 26-18 gauge.


1. String bead on to The top or eye pin.
Minimize the wire about 8-10mm from the
bead.
two. Use non-serrated chain-nose pliers to
bend the wire just previously mentioned the bead.
3. Use round-nose pliers to grasp the idea of
the wire, and bend it round the pliers.
4. Bring the idea with the wire all of the way
all-around again to your bead.
5. If essential, use non-serrated chain-nose
pliers to straighten the loop.
one. String bead on to The top or eye pin.
Use non-serrated chain-nose pliers to
bend the wire just over the bead.
2. Slash the wire from about eight-10mm from
the bead.
3. Use round-nose pliers to grasp the idea of
the wire, and bend it round the pliers.
Carry the tip in the wire all of the way
around again on the bead.
4. If vital, use non-serrated chain-nose
pliers to straighten the loop.




Wire-Wrapped Loops
For finest benefits, use each chain-nose and spherical-nose pliers. Aventurine Rosary
by Rita Hutchinson
The 1-stage looper made brief get the job done of this rosary.
Blue Pin Stripe Bracelet
by Amy Mickelson
Wire-wrapped ball-conclusion head pins make classy dangles.
Brass Arrow Earrings
by Mollie Valente
2-loop beaded connectors
built with wire.
Tip: make use of the rounding portion of crimp
pliers to tuck within the trimmed close of
the wire wrap.
one. String bead onto The pinnacle or eye pin.
2. Use chain-nose pliers to grasp the wire
just above the top of your bead and bend.
3. Use spherical-nose pliers to grasp a spot
just higher than the bend, and make use of your
fingers to effortlessly bend the wire the many
way across the idea in the pliers. (For
unique measurements of loops, bend the wire
all-around thinner or thicker portions with the
pliers’ idea.) You need to have a two-3mm
stem of straight wire in between the bead
as well as bend.
Annie Get Your Pearls Earrings

A wire wrapped end on these
sterling silver head pins provides added
stability when applying larger close
elements like SWAROVSKI
Things crystal.
4. Meticulously wrap the surplus wire around
the wire stem with the loop down
to the bead. For ideal control, authorities
recommend you split this move into a
number of half wraps.
5. Hold wrapping until you get to the bead.
6. Trim surplus with flush cutters.


Ways to Open and shut Soar Rings
Whenever you open up and shut bounce rings, twist sideways as opposed to
“ovalling” them. This retains their shape far better, that makes them
much easier to close every one of the way. To forestall marks over the ring, use nonserrated flat-nose pliers.
Twist finishes absent
from each other
Don’t pull apart
sideways
Enlarging Chain Links
If an oval chain website link is a little bit too tiny for your personal jump ring, try men's college ring out utilizing a
force-pin or an awl to somewhat round/enlarge it by laying the tip backlink
with a telephone ebook (or Rings & Points catalog), and firmly urgent the
awl or push-pin into it.
Un-Soldered Chain Backlinks
Open up un-soldered chain inbound links the same way you should a jump ring.
Double Leap Rings
Double them up for further protection, or a series-mail glimpse.
Bounce Ring Device
By Beadalon®. For this sort of an easy wanting Software, this is the big assist when
you’re working with leap rings. It matches on your own finger similar to a ring. Decide on
out the slot on the tool that fits the wire gauge of your soar ring,
twist and maintain the soar ring open up. Merchandise #sixty nine-079
Sorts of Crimps
Ways to Use Crimps

Crimp Beads
Crimp Handles
Centre-Crimps
Fold Over Crimps
Crimp Finishes
Crimp beads and tubes present you with a protected and Experienced complete For lots of
types of layouts. Use crimp beads or tubes with a clasp, or use centercrimps or crimp finishes given that the clasp.
Choosing Crimps
Wire Diameter Crimp Bead Sizing Crimp Tube Sizing
0.010” (0.25mm) 0, one 0,one
0.012” (0.30mm) men's gold & silver rings 0, 1 0,1
0.013” (0.33mm) 0, one 1
0.015” (0.38mm) one two
0.018” (0.46mm) one two
0.020” (0.51mm) 2 2
0.021” (0.53mm) 2 2
0.024” (0.61mm) two, three two, 3
0.030” (0.76mm) 3 4
0.036” (0.91mm) three four
Dimensions 0 Dimensions one Measurement 2 Dimension 3 Size 4
Crimping Equipment
To simply flatten a crimp You should use flat-nose pliers. For a more
Expert appear, you can fold and around the crimps with crimp
pliers. There are a number of crimping pliers out there. Here's a useful
chart that can assist you decide on the suitable pliers:
Pliers Item # Crimp Size
five” Crimper sixty five-010 #1 and #2 beads
#two and #three tubes
5” Micro Crimper sixty five-011 #one tubes
5” Mighty Crimper 65-012 #3 and #four beads
#four crimp tubes
3.five” Pocket Crimper sixty nine-215 #1 and #two beads
#two and #3 tubes

1. String a crimp bead on to the beading
twine or cable, then the clasp.
2. Bend the cable back in the
crimp bead.
three. Tighten up the loop. Use crimping
pliers to crimp the bead into a small
rounder crimp, or use flat-nose pliers
to easily flatten the crimp.
four. Trim the excess wire/cable.
five. Use crimping pliers to close a crimp
address about the crimp bead.
• For all crimping, use stress comparable to a organization handshake, but don’t squeeze so
challenging that you're employed-harden the crimp and help it become brittle or break your tool.
• Utilize a crimp go over to hide the crimp inside of what appears like a 3-4mm spherical bead.
• Tiny center-crimp tubes may perhaps call for needle-nose pliers or good-tipped flat-nose pliers.
Using EURO men's college ring Resource® Crimping Pliers Finishing a Necklace or Bracelet
one. Use the surface indent to shape the crimp
into an oval.
two. With all the wire on both side with the indent,
use the interior indent to safe the crimp
around the twine.
3. Move the crimp again for the outer indent
to fold it right into a round condition.
Havasu Falls Necklace
by Polly Nobbs-Larue
Polly utilised crimps to finish the multi-strand
part of this necklace.

French Wire (aka Bullion)
Bullion (or French wire) was originally utilized to
finish silk bead wire ends, generally for pearl
necklaces. It's attained acceptance as an gents ring elegant
way to complete/hide the uncovered end loops of
beading cable likewise (tigertail, Beadalon®, Gentle
Flex®, and many others.)
Close-up Perspective
Cable Thimbles/Wire Guardians™
Much like bullion, but sturdier, this preformed
channel helps prevent fraying on stringing cable
and cord. It will likely be positioned in which you make
a loop to attach the clasp. Don’t pinch shut
— the horseshoe design and style permits some slack
within the wire to cut back strain.
Silver Shamrock Bracelet
by Polly Nobbs-LaRue
Cable thimbles each
guard the beading cable
and include a pretty,
finished seem.
one. Lower two parts in precise equal
lengths (approx ½-¾”).
two. Include just one crimp men's gold & silver rings or finishing bead
and one particular bit of bullion towards the
conclusion of wire cable. Slide the clasp
more than the bullion.
three. Loop the cable again with the
crimp or bead.
four. Pull Carefully till the finishes of
the bullion are flush versus the
crimp bead or tucked inside the
finishing bead.
five. If using a crimp bead, crimp
closed and canopy using a crimp
address.
Take a look at our whole Education Station on the internet!

Shut-up View
1. String the cable thimble on to the
wire.
two. Loop the cord back again from the
other side in the cable thimble.
three. String the clasp on to the wire &
thimble.
4. Crimp cording alongside one another.

 

Greatest Jewelry Fundamental principles





Essential Wire Loops
For finest results, use the two chain-nose and round-nose pliers.
Approach 2 – Bend then cut
Technique 1 – Reduce then bend
Technique 3 – Use the 1-Action Looper
one two 3
4 five 6
From your Beadsmith® R&T Item #69-055
Trim and loop eye pins in one movement. Performs with 3/8” wire and
lengthier. Use dead-soft or 50 percent-really hard precious metallic wire, craft wire, and
copper or brass core wire. Use with wire in between 26-eighteen gauge.


one. String bead onto the head or eye pin.
Slice the wire about eight-10mm through the
bead.
2. Use non-serrated chain-nose pliers to
bend the wire just over the bead.
3. Use spherical-nose pliers to grasp the suggestion of
the wire, and bend it across the pliers.
4. Provide the suggestion with the wire all of the way
around again to your bead.
five. If essential, use non-serrated chain-nose
pliers to straighten the loop.
one. String bead on to the head or eye pin.
Use non-serrated chain-nose pliers to
bend the wire just higher than the bead.
two. Lower the wire from about 8-10mm from
the bead.
three. Use spherical-nose pliers to grasp the tip of
the wire, and bend it around the pliers.
Provide the suggestion of the wire the many way
close to again on the bead.
4. If vital, use non-serrated chain-nose
pliers to straighten the loop.




Wire-Wrapped Loops
For ideal final results, use both chain-nose and spherical-nose pliers. Aventurine Rosary
by Rita Hutchinson
The 1-step looper built swift perform of the rosary.
Blue Pin Stripe Bracelet
by Amy Mickelson
Wire-wrapped ball-conclude head pins make elegant dangles.
Brass Arrow Earrings
by Mollie Valente
two-loop beaded connectors
produced with wire.
Tip: utilize the rounding portion of crimp
pliers to tuck in the trimmed conclusion of
the wire wrap.
1. String bead on to The top or eye pin.
two. Use chain-nose pliers to grasp the wire
just earlier mentioned the top of your bead and bend.
3. Use spherical-nose pliers to grasp a place
just above the bend, and make use of your
fingers to effortlessly bend the wire every one of the
way around the suggestion in the pliers. (For
distinctive measurements of loops, bend the wire
all-around thinner or thicker parts of your
pliers’ tip.) You ought to have a 2-3mm
stem of straight wire concerning the bead
along with the bend.
Annie Obtain your Pearls Earrings

A wire wrapped finish on these
sterling silver head pins provides extra
protection when utilizing better finish
factors like SWAROVSKI
Components crystal.
four. Very carefully wrap the surplus wire all-around
the wire stem from your loop down
into the bead. For very best Regulate, experts
advocate you crack this step right into a
number of half wraps.
five. Continue to keep wrapping until you reach the bead.
six. Trim excess with flush cutters.


The best way to Open up and Close Leap Rings
Once you open up and shut bounce rings, twist sideways as opposed to
“ovalling” them. This retains their shape far better, that makes them
much easier to close every one of the way. To circumvent marks on the ring, use nonserrated flat-nose pliers.
Twist ends away
from one another
Don’t pull aside
sideways
Enlarging Chain Links
If an oval chain website link is a tiny bit as well modest for your personal leap ring, check out using a
press-pin or an awl to a little spherical/enlarge it by laying men's fashion rings the end website link
over a cellular phone guide (or Rings & Items catalog), and firmly urgent the
awl or force-pin into it.
Un-Soldered Chain Hyperlinks
Open un-soldered chain inbound links the same way you'd a leap ring.
Double Soar Rings
Double them up for more security, or a chain-mail appear.
Soar Ring Device
By Beadalon®. For this kind of an easy wanting Software, this is a large aid when
you’re dealing with soar rings. It suits on the finger similar to a ring. Pick
out the slot around the Instrument that fits the wire gauge of one's jump ring,
twist and hold the leap ring open. Item #69-079
Varieties of Crimps
How you can Use Crimps

Crimp Beads
Crimp Covers
Middle-Crimps
Fold Above Crimps
Crimp Ends
Crimp beads and tubes provide a secure and Skilled end For several
forms of patterns. Use crimp beads or tubes using a clasp, or use centercrimps or crimp ends since the clasp.
Deciding on Crimps
Twine Diameter Crimp Bead Measurement Crimp Tube Measurement
0.010” (0.25mm) 0, 1 0,1
0.012” (0.30mm) 0, 1 0,1
0.013” (0.33mm) 0, 1 one
0.015” (0.38mm) one two
0.018” (0.46mm) 1 2
0.020” (0.51mm) 2 two
0.021” (0.53mm) two two
0.024” (0.61mm) two, 3 2, 3
0.030” (0.76mm) 3 4
0.036” (0.91mm) three four
Dimensions 0 Dimensions one Measurement 2 Dimension 3 Size 4
Crimping Applications
To easily flatten a crimp You may use flat-nose pliers. For a far more
Specialist seem, you are able to fold and round the crimps with crimp
pliers. There are a variety of crimping pliers available. Here's a helpful
chart that may help you opt for the suitable pliers:
Pliers Item # Crimp men's gold & silver rings Size
five” Crimper sixty five-010 #1 and #2 beads
#two and #three tubes
5” Micro Crimper sixty five-011 #one tubes
5” Mighty Crimper 65-012 #three and #4 beads
#4 crimp tubes
three.5” Pocket Crimper 69-215 #one and #two beads
#2 and #three tubes

one. String a crimp bead onto the beading
cord or cable, then the clasp.
two. Bend the cable back again throughout the
crimp bead.
3. Tighten up the loop. Use crimping
pliers to crimp the bead into a little
rounder crimp, or use flat-nose pliers
to easily flatten the crimp.
4. Trim the surplus twine/cable.
5. Use crimping pliers to shut a crimp
deal with in excess of the crimp bead.
• For all crimping, apply pressure just like a agency handshake, but don’t squeeze so
tough that you work-harden the crimp and enable it to be brittle or split your Instrument.
• Use a crimp deal with to hide men's college ring the crimp inside what seems like a 3-4mm round bead.
• Little Centre-crimp tubes may well demand needle-nose pliers or fine-tipped flat-nose pliers.
Applying EURO Device® Crimping Pliers Finishing a Necklace or Bracelet
one. Use the surface indent to shape the crimp
into an oval.
two. With all the gents ring wire on both side of your indent,
make use of the inner indent to protected the crimp
across the wire.
three. Move the crimp back again towards the outer indent
to fold it right into a round condition.
Havasu Falls Necklace
by Polly Nobbs-Larue
Polly utilised crimps to finish the multi-strand
part of this necklace.

French Wire (aka Bullion)
Bullion (or French wire) was originally utilized to
complete silk bead twine ends, principally for pearl
necklaces. It men's gold & silver rings has attained reputation as a sublime
way to finish/disguise the exposed close loops of
beading cable at the same time (tigertail, Beadalon®, Soft
Flex®, and many others.)
Close-up Watch
Cable Thimbles/Wire Guardians™
Similar to bullion, but sturdier, this preformed
channel helps prevent fraying on stringing cable
and cord. It is frequently placed in which you make
a loop to attach the clasp. Don’t pinch closed
— the horseshoe structure allows for some slack
over the cord to lower tension.
Silver Shamrock Bracelet
by Polly Nobbs-LaRue
Cable thimbles both equally
safeguard the beading cable
and increase a lovely,
concluded seem.
one. Reduce two parts in exact equivalent
lengths (approx ½-¾”).
2. Increase 1 crimp or ending bead
and one piece of bullion into the
stop of wire cable. Slide the clasp
about the bullion.
3. Loop the cable back again in the
crimp or bead.
4. Pull gently right until the ends of
the bullion are flush from the
crimp bead or tucked In the
finishing bead.
5. If employing a crimp bead, crimp
closed and cover that has a crimp
cover.
Look into our comprehensive Training Station on the web!

Shut-up See
1. String the cable thimble on to the
twine.
two. Loop the cord back throughout the
other facet from the cable thimble.
3. String the clasp on to the wire &
thimble.
four. Crimp cording with each other.

 

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15